- Engine Products
- Exhaust Products
- Tech Tips, News & More
- Free Tech Tips
- #153 Hurth HBW50/100/125/150 Transmissions: Two Common Problems Easily Avoided
- #155: Chrysler LH318 & LH360 Industrial Engines: Easy Block Repair
- #141 Deutz Diesel Engine Model 1013 Fuel Transfer Pumps
- #142 Ford 330 Industrial Engines: Identifying the Dorset and the Dagenham Models
- #143 How NOT To Seat the Piston Rings on Your New Ford 300 Industrial Engine; Cleaning Components When Swapping Accessories
- #144 Deutz 1011 and 2011 Timing Belt Tension
- #145 Installing an Electronic Governor: Five Easy Tips
- #146 Yanmar Engine Tag Locations
- #147 Running a Twin Disc/Rockford? Want It To Last Longer?
- #148: Ford Industrial In-Line 6 Cylinder Gas Engines: How to Tell Them Apart
- #154: AutoClutch Power Takeoff Clutches
- All Tech Tips
- Ask Dr. Diesel
- Industry Links
- Guides, Forms & Tags
- Company Info
- Contact Us
The Nuts and Bolts of Con Rod Reconditioning
Helpful tip with reconditioning the Con Rod - Tech Tip #76
This Tech Tip, The Nuts and Bolts of Con Rod Reconditioning, is one of an ongoing series of Foley Tech Tips that we publish. We hope that the information provided will be valuable to you.
People sometimes ask our Dr. Diesel "What's the big deal with the emphasis at Foley Engines on connecting rod reconditioning?" After all, they say, some engine rebuilders just put the old con rods back in when rebuilding engines. We feel strongly that rods used in marine and industrial applications should always be reconditioned using all new fasteners. That's why our Foley Engine kits contain new piston pins, new rod bushings, new rod bolts and nuts, and a Workshop Manual for Deutz, Deere and Perkins engines to give you all the specs. Our dealers and customers tell us that no one else has kits that are this complete.
Round bores, concentric bores, and straight rods. The goal should be to assemble the engine with connecting rods that have been checked for straightness, twist, and original center to center specifications. In smaller 4 and 6 cylinder diesel engines, the rods should be machined back to original specs with no more than .002¼ of bend and .004¼ of twist in the rod. A rod with too much bend will limit oil clearances from one side to the other and possibly lock up the engine at the pin end or thrust on the crankshaft. When we recondition a connecting rod we use a rod cap grinder and remove approximately .002¼ from both the rod and the cap. When the rod and cap are reassembled and torqued, there will be about .003¼ to hone out of the big end using a Sunnen rod hone. A con rod that can not be brought back to factory specs (Ðead nuts as an automotive machinist would say) should be discarded. The risk of damaging the engine block is too great and brand new rods are very inexpensive (new Perkins and Deere rods can be as low as $100).
Lets take rod bolts next.. People ask us why we stress the importance of using new connecting rod nuts and bolts in a Deutz or Perkins engine. They note that we put new con rod fasteners into all of our Foley Engine overhaul parts kits. (Dr. Diesel fought hard for this here at Foley Engines. These fasteners aren't cheap!) Simply put, your old rod bolts and nuts have stretched over millions of engine cycles. You can even prove that by measuring rod bolt length with a micrometer or a specialty gauge that is fitted with a dial indicator. Both BHJ Products (510 797 6780) and Goodson Shop Supplies, Goodson Part Number RBG-1, (800 533 8010) have rod bolt stretch gauges. The maximum stretch from the relaxed length to the length of the bolt when installed and torqued to value should be no more than .006¼ Rather buying a guage and measuring your old bolts you can replace them easily and cheaply with new ones. When an old rod bolt fatigues and stretches, bad things can happen. The rod no longer is at a consistent height with the other rods, the bolt is not at peak strength, the big end is no longer round, and soon the the engine will throw the rod creating a window in your block. (Wall St. types in pink shirts who never took automotive shop class sometimes think TRW stands for Thompson, Ramo and Woolridge, the automotive parts conglomerate that was created out of Thompson Wire. Now you know what TRW really means.)
Piston Pins and Bushings
People also ask us what the big deal is about installing new piston pin bushings and new piston pins. Sure, you could cheat and use the old ones, but in a compression firing diesel engine, the length of the rod and the strength of the rod to piston connection are critical. We think that re-using the old pins and bushings is false economy. Take it from the diesel remanufacturing industry, always install new small end bushings and pin fit your con rods. Take a look at Foley Tech Tip # 6 for more info on handy tips on how to install rod bushings. Finally, piston pins are also very important. They of course connect the rod to the piston. If a piston pin lets go, you now have a nice gouge in the wall of your engine's liner or even block. Surprisingly John Deere liner kits from John Deere dealers don't contain any piston pins. We've learned better over the last 97 years (we were founded in 1916!) and ship new piston pins with all of our kits. Do you deserve anything less?
Please call us with our comments or suggestions. We take tech support seriously and want to advance the knowledge base in our field.
We take tech support seriously!
We hope that you will find this Tech Tip helpful. We believe that Tech Support matters and welcome your comments or suggestions.
Please email Dr. Diesel using our contact form or call us at 800.233.6539.